Call Us
+86 136 6007 9809
Call Us
+86 136 6007 9809
Aug. 30, 2026
The rapid expansion of AI computing is increasing the demand for high-density data center infrastructure.
Higher computing loads require extensive electrical distribution, power conversion, thermal management and mechanical support systems.
Behind these systems are thousands of mechanical connections.
Electrical cabinets, power distribution equipment, busbar assemblies, cooling systems, cable management structures, battery systems and supporting equipment all depend on fasteners and precision mechanical components that are
compatible with their specific design requirements.
JUXIN manufactures custom industrial fasteners and CNC machined components for data center electrical equipment, power infrastructure and supporting systems.
Our capabilities include screws, bolts, nuts, studs, washers, threaded components, pins, spacers, bushings, standoffs and custom CNC machined parts.
Components can be manufactured according to engineering drawings, technical specifications and customer-defined material and surface-treatment requirements.
Fasteners are small components, but they form mechanical connections throughout critical infrastructure.
In an AI data center, fasteners may be used in:
Electrical cabinets
Power distribution equipment
Busbar assemblies
Power electronics
Cooling equipment
HVAC systems
Cable management systems
Battery systems
Equipment frames
Structural assemblies
The requirements can vary significantly between applications.
A fastener used inside an electrical cabinet may have different requirements from a fastener used in a cooling system or structural support.
Therefore, the correct fastener should be selected according to the actual mechanical, environmental and installation requirements.
Electrical equipment manufacturers frequently use proprietary cabinet, enclosure and mounting designs.
Standard catalog hardware may not always match the required:
Thread
Length
Head configuration
Material
Surface treatment
Installation space
Mounting interface
JUXIN manufactures custom fasteners according to customer drawings and specifications.
Potential products include:
Custom screws
Electrical cabinet screws
Industrial bolts
Custom nuts
Studs
Threaded pins
Washers
Spacers
Standoffs
Special threaded components
Custom manufacturing allows the fastener to match the equipment design rather than forcing the equipment design around standard hardware.
AI data centers require substantial electrical infrastructure to distribute power to computing systems and supporting equipment.
Power distribution assemblies can include:
Electrical cabinets
Distribution panels
Power conversion equipment
Switchgear
Power electronics
Busbar systems
Equipment frames
Mounting structures
Fasteners can be used to secure covers, brackets, panels, supports and mechanical assemblies.
Depending on the equipment, engineers may evaluate:
Mechanical strength
Thread compatibility
Material
Corrosion resistance
Electrical considerations
Installation method
Surface treatment
Environmental exposure
JUXIN supports OEM manufacturers with custom fasteners for electrical and power equipment assemblies.
Busbar systems are an important part of electrical power distribution.
Mechanical components associated with busbar assemblies may include:
Bolts
Nuts
Washers
Studs
Spacers
Supports
Custom machined components
The specific fastening requirements depend on the busbar design and electrical system.
Mechanical fasteners should be specified according to the equipment manufacturer's engineering requirements, including dimensions, material, clamping requirements and applicable electrical considerations.
For custom busbar-related mechanical components, JUXIN can manufacture parts according to engineering drawings.
Electrical cabinets and enclosures require numerous small mechanical components.
Fasteners can be used for:
Cabinet panels
Mounting brackets
Covers
Internal supports
Control modules
Cable-management hardware
Cooling components
Depending on the enclosure environment, engineers may specify carbon steel, stainless steel, coated steel or other materials.
Surface treatment can also influence corrosion resistance, appearance, thread fit and dimensional characteristics.
JUXIN can manufacture standard and custom fasteners for electrical equipment based on customer specifications.
Power density and computing performance make thermal management an important part of modern data center infrastructure.
Cooling equipment can include:
HVAC systems
Cooling modules
Heat exchangers
Liquid-cooling equipment
Pump assemblies
Pipe-support structures
Cooling cabinets
Mechanical frames
Fasteners used in these systems may be exposed to:
Moisture
Temperature variation
Condensation
Vibration
Corrosive environments
Repeated maintenance
Material and surface treatment should therefore be selected according to the actual operating environment.
JUXIN supplies custom fasteners for cooling equipment and HVAC assemblies, including screws, bolts, nuts, studs and CNC machined components.
Liquid cooling systems introduce additional mechanical interfaces.
Depending on the equipment architecture, fasteners may be used around:
Cooling modules
Manifolds
Pump assemblies
Mounting brackets
Pipe supports
Equipment frames
Service panels
The fastener specification should consider the surrounding environment and the mechanical function of the joint.
Where moisture or condensation is expected, corrosion resistance may become an important material-selection factor.
For custom components, JUXIN can manufacture stainless steel and coated fasteners according to customer drawings and requirements.
Stainless steel may be selected when corrosion resistance, durability or environmental compatibility is important.
Potential applications include:
Cooling equipment
HVAC systems
Electrical enclosures
Outdoor equipment
Equipment frames
Mechanical assemblies
Depending on the application, stainless steel grades such as 304 or 316/316L may be considered.
The appropriate grade should be determined according to the actual environment, mechanical requirements and customer specification.
JUXIN can manufacture custom stainless steel screws, bolts, nuts, studs and CNC machined components.
Carbon steel and alloy steel fasteners remain suitable for many industrial assemblies where strength and cost efficiency are important.
Potential applications include:
Equipment frames
Structural assemblies
Mounting brackets
Mechanical supports
Industrial machinery
HVAC equipment
Depending on the application, surface treatments such as zinc plating, zinc-nickel plating or zinc-aluminum flake coatings may be considered for corrosion protection.
For high-strength fasteners, the applicable strength grade and manufacturing requirements should be clearly defined in the engineering specification.
Aluminum is frequently used in equipment where low weight, machinability or specific thermal and electrical characteristics are important.
JUXIN can manufacture aluminum CNC components such as:
Spacers
Standoffs
Brackets
Bushings
Mounting components
Custom housings
Precision mechanical parts
Material selection should consider the mechanical load, thermal environment, electrical requirements and compatibility with mating materials.
Data center equipment manufacturers often require more than standard fasteners.
Custom mechanical components may include:
Precision pins
Shafts
Bushings
Spacers
Standoffs
Brackets
Sleeves
Mounting components
Custom fixtures
JUXIN provides CNC turning and CNC machining for custom industrial components.
CNC machining is particularly useful when a component contains integrated features that cannot be efficiently produced as standard hardware.
For example:
Shaft + Shoulder + Groove + Thread + Precision Diameter
These features can be manufactured as an integrated component according to the engineering drawing.
Threaded components are widely used throughout electrical and mechanical equipment.
Custom requirements may include:
Fine threads
Metric threads
Unified threads
Internal threads
External threads
Threaded shafts
Threaded pins
Special studs
Custom nuts
For precision equipment, engineers may also need to define:
Thread tolerance
Thread engagement
Runout
Concentricity
Surface finish
JUXIN manufactures custom threaded components according to customer drawings and specifications.
Surface treatment can affect corrosion resistance, friction, appearance and dimensional characteristics.
Depending on the application, JUXIN can support requirements involving:
Zinc plating
Trivalent chromium zinc plating
Zinc-nickel plating
Zinc-aluminum flake coatings
PTFE-based coatings
Passivation
Mechanical polishing
Customer-specified finishes
The appropriate finish depends on the substrate, environment and application.
For electrical and data center equipment, engineers should also consider whether the surface treatment affects thread fit, electrical contact, grounding interfaces or other functional requirements.
Data center equipment is often installed in controlled indoor environments, but some mechanical systems may still experience moisture, condensation or temperature variation.
Cooling systems can create different environmental conditions from electrical cabinets or indoor equipment frames.
Corrosion protection may therefore be considered according to:
Material + Environment + Surface Treatment + Service Conditions
Stainless steel may be appropriate for selected environments, while coated carbon steel may provide a practical solution for other industrial applications.
The correct selection should be based on the actual application rather than applying one material to every data center component.
High-density data centers require extensive cable and power management infrastructure.
Fasteners can support:
Cable trays
Brackets
Mounting rails
Cable-management structures
Equipment panels
Support frames
Custom screws, bolts, nuts, spacers and standoffs can be manufactured according to the required mounting interface.
For space-constrained installations, custom head configurations or non-standard lengths can also be considered.
Data center power infrastructure may include battery systems and energy-storage equipment.
Mechanical components can be required for:
Battery enclosures
Mounting brackets
Equipment frames
Covers
Structural supports
Electrical assemblies
Material, corrosion resistance, mechanical strength and installation requirements should be evaluated according to the battery-system design.
For custom components, JUXIN can manufacture fasteners and CNC machined parts from customer drawings.
Power electronics equipment may require compact mechanical assemblies containing both electrical and mechanical components.
Fasteners can be used for:
Mounting plates
Heat-management assemblies
Electrical enclosures
Brackets
Covers
Power modules
Equipment frames
Engineers may need to consider mechanical load, thermal conditions, material compatibility, electrical interfaces and assembly access.
JUXIN supports custom fastening components for industrial power electronics and related equipment.
Data centers depend on extensive HVAC and mechanical infrastructure.
Fasteners may be used throughout:
HVAC equipment
Cooling units
Ductwork
Equipment housings
Pipe supports
Mechanical frames
Access panels
These applications may require different fastener materials and surface treatments depending on indoor conditions, humidity, condensation and equipment location.
JUXIN can support both standard industrial fasteners and custom components for HVAC equipment manufacturers.
Fans, pumps, compressors and other mechanical systems can generate vibration.
Fastener selection should therefore consider:
Joint design
Clamping force
Fastener strength
Thread engagement
Installation torque
Vibration conditions
Locking requirements
For selected applications, locking nuts, prevailing-torque nuts or other engineered fastening methods may be appropriate.
The correct solution should be determined by the joint design and equipment requirements.
Data center equipment manufacturers frequently develop proprietary mechanical designs.
This can create requirements for:
Non-standard dimensions
Special head geometries
Custom threads
Custom lengths
Special materials
Specific surface treatments
Precision CNC components
JUXIN supports drawing-based manufacturing for OEM customers.
Customers can provide:
Engineering drawings
CAD files
Technical specifications
Existing samples
Part numbers
Material requirements
Our manufacturing team can review the requirements before production.
A reliable industrial fastener program begins with a clear specification.
JUXIN reviews requirements such as:
Steel, stainless steel, aluminum, alloy steel or other specified materials.
Diameter, length, head geometry and other critical dimensions.
Thread standard, pitch, tolerance and engagement.
Required mechanical strength or specified grade.
Plating, coating, passivation, polishing or other specified finish.
Humidity, temperature, corrosion exposure and other service conditions.
Critical dimensions, inspection methods and documentation.
Packaging requirements for production, storage and assembly.
This process helps connect the customer's engineering requirements with a repeatable manufacturing process.
Modern data center equipment can contain many different mechanical components.
An electrical cabinet assembly may require:
Screws + Nuts + Studs + Spacers + Standoffs + Brackets + CNC Components
Cooling equipment may require:
Bolts + Washers + Studs + Bushings + Shafts + Mounting Components
Sourcing multiple component categories from one qualified supplier can simplify RFQ management and technical communication.
JUXIN combines:
Fastener Manufacturing + CNC Turning + CNC Machining + Surface-Treatment Coordination
This allows us to support broader mechanical component requirements for industrial OEM equipment.
For procurement managers and supply-chain teams, fastener sourcing is not only about unit price.
Supplier evaluation may include:
Manufacturing capability
Material sourcing
Drawing interpretation
Quality control
Thread consistency
Dimensional repeatability
Surface-treatment capability
Production capacity
Packaging
Technical communication
Long-term supply stability
For recurring OEM programs, maintaining consistent specifications across production batches is particularly important.
JUXIN works with customers on drawing-based production to support repeat orders and long-term industrial supply programs.
Structural engineers and mechanical design engineers should evaluate fasteners as part of the complete assembly.
Key considerations may include:
Load → Joint Design → Fastener Grade → Thread → Material → Environment → Installation
For electrical equipment, additional considerations may include:
Electrical Interface → Grounding Requirements → Material Compatibility → Surface Treatment
For cooling equipment:
Temperature → Moisture → Corrosion → Vibration → Joint Stability
The final fastener specification should reflect the actual equipment function.
JUXIN custom fasteners and CNC components can support:
AI data center equipment
Data center electrical infrastructure
Power distribution equipment
Electrical cabinets
Busbar assemblies
Power electronics
Cooling systems
Liquid cooling equipment
HVAC equipment
Cable management systems
Battery systems
Equipment frames
Mechanical support structures
The required material, strength, surface treatment and dimensions should be established according to each application.
The same manufacturing capabilities can support a wide range of industrial applications.
Typical markets include:
Electrical equipment
Power electronics
Telecommunications
Industrial automation
Robotics
HVAC
Renewable energy
Solar equipment
EV manufacturing equipment
Industrial machinery
Rail transit
Electronics manufacturing
This gives OEM customers the flexibility to source multiple categories of custom mechanical components from one industrial supplier.
JUXIN has more than 23 years of fastener industry experience and supports international OEM customers requiring custom fasteners and precision mechanical components.
Our capabilities combine:
Industrial Fastener Manufacturing + CNC Turning + CNC Machining + Custom Surface Treatment
We can support:
Custom screws
Industrial bolts
Nuts
Studs
Washers
Threaded components
Stainless steel fasteners
Coated steel fasteners
Precision pins
Shafts
Bushings
Spacers
Standoffs
Brackets
Custom CNC components
Our objective is to manufacture components according to the customer's approved engineering drawings and application requirements.
If you are sourcing fasteners for AI data center power infrastructure, electrical equipment, cooling systems or supporting mechanical assemblies, JUXIN can review your drawings, CAD files, specifications or samples.
Please provide:
Engineering drawing
CAD file, if available
Part number
Material
Fastener standard
Thread specification
Strength requirement
Surface treatment
Corrosion-resistance requirement
Application environment
Inspection requirements
Annual or project quantity
Packaging requirements
Our team can review your requirements and determine an appropriate manufacturing approach before quotation.
Email: info@juxinfasteners.com
Website: www.juxinfasteners.com
JUXIN FASTENERS — Custom Industrial Fasteners and CNC Components for AI Data Center Infrastructure, Electrical Equipment and Global OEM Supply Chains.
Fastener selection depends on the actual equipment design, joint requirements, operating environment and applicable engineering specifications. Final material, strength, surface treatment and dimensional requirements should be confirmed before production.
Contact Us
Tel.:
+86 020 8621 0320
+86 020 3121 6067
E-mail:
Technical Support:
Navigation
SEND INQUIREY
